PRODUCT INFORMATION
Product Overview
The General Electric IC695PSD040 is a Power Supply module for the PACSystems RX3i series. This rack power supply mounts directly into slot 0 of an RX3i universal backplane. It operates from a nominal 24 VDC input source. The start voltage requirement spans 18 to 30 VDC. The module run voltage range extends from 12 to 30 VDC. Input power reaches a maximum of 60 Watts at full load. Total output power does not exceed 40 Watts.
The module supplies 5.1 VDC at up to 6 Amps. It also provides 3.3 VDC at up to 9 Amps. Each logic rail delivers a maximum of 30 Watts within the 40-Watt total limit. A dedicated 24 VDC output energizes circuits on relay output modules. A 10 ms ride-through time maintains output during transient input voltage drops. Four front LEDs indicate power status, supply fault, overtemperature, and overload conditions. A front toggle switch controls local module power.
TECHNICAL DATA
Technical Specifications
| Parameter | Specification |
|---|
| Controller Redundancy | Not supported |
|---|
| Increased capacity mode | Not supported |
|---|
| Input Power | 60 Watts, maximum |
|---|
| Input Voltage | Start: 18 to 30 VDC Run: 12 to 30 VDC |
|---|
| Input voltage range | 18 to 30 VDC |
|---|
| Inrush Current | 4 Amps, 100 milliseconds maximum |
|---|
| Installation | RX3i universal backplane |
|---|
| Isolation | None |
|---|
| LED Indicators | 4 |
|---|
| Nominal Rated Voltage | 24 VDC |
|---|
| Number of Daisy-Chained PSD040 | Two (2) |
|---|
| On/Off Switch | Yes |
|---|
| Output Current | 5.1 VDC: 0 to 6 Amps 3.3 VDC: 0 to 9 Amps |
|---|
| Output Power | 40 Watts, maximum |
|---|
| Output Voltage | 5.1 VDC; 3.3 VDC |
|---|
| Outputs | 3 |
|---|
| Power Supply | 40 Watts |
|---|
| Power supply Redundancy | Not supported |
|---|
| Product Description | Power Supply Module |
|---|
| Product Line | RX3i PacSystem |
|---|
| Ride through time | 10 ms |
|---|
| Ripple | 50 mV |
|---|
| Slot Assignment | Slot 0 |
|---|
| Start Voltage Range | 12 to 30 VDC |
|---|
| Terminal Current | 6 Amps |
|---|
| Voltage Range | 18 to 30 VDC |
|---|
| Weight | 1.31 lbs (0.60 kg) |
|---|
| Wiring Terminals | 14 AWG to 18 AWG wire |
|---|
TECHNICAL INFORMATION
Features
- Delivers up to 40 Watts total output power to the backplane.
- Provides 5.1 VDC at 0 to 6 Amps and 3.3 VDC at 0 to 9 Amps.
- Supplies 24 VDC output power to energize relay output circuits.
- Provides 10 ms holdup ride-through time during input voltage drops.
- Includes four diagnostic LEDs for power, fault, overtemperature, and overload.
- Features a front-mounted switch for manual on and off control.
- Supports daisy-chain connection of up to two units without increasing capacity.
TECHNICAL INFORMATION
Connections / Interfaces
- Backplane connector interfaces directly with Slot 0 of an RX3i universal backplane.
- Field wiring terminals accommodate 14 AWG to 18 AWG wiring for DC input power.
TECHNICAL INFORMATION
Installation Guidelines
- Mount the module directly into Slot 0 of the RX3i universal backplane.
- Connect input power conductors sized between 14 AWG and 18 AWG.
- Verify that total backplane power demand does not exceed 40 Watts.
TECHNICAL INFORMATION
Configuration Guidelines
- Install only one power supply module per RX3i universal backplane.
- This power supply does not support redundant or increased capacity configurations.
- Move modules to an expansion backplane if power consumption exceeds 40 Watts.
- Daisy-chaining two units does not increase total backplane power capacity.
TECHNICAL INFORMATION
Compatibility
- PACSystems RX3i universal backplane
- PACSystems RX3i relay output modules
COMPATIBILITY
Compatibility & Replacement
COMPATIBLE MODELSPACSystems RX3i universal backplane PACSystems RX3i relay output modules
Verify compatibility against the exact Part Number, revision and manufacturer documentation before ordering.
PART VERIFICATION
Before You Order
Industrial automation parts can share similar model names, suffixes and revisions. Confirm the complete manufacturer Part Number before purchase.
01Check Part NumberMatch the complete ordering code on the existing unit.
02Confirm RevisionCheck suffix, hardware or firmware when applicable.
03Send a Label PhotoWe can review a clear label photo when identification is uncertain.
ORDERING PROCESS
From RFQ to Dispatch
1Submit Part Number2Verify Product Identity3Confirm Stock & Condition4Issue Quotation5Dispatch & Tracking
PRODUCT FAQ
Frequently Asked Questions
Which slot does the IC695PSD040 occupy in the backplane?
The IC695PSD040 installs into Slot 0 of an RX3i universal backplane. It occupies one slot.
Does the IC695PSD040 support redundant operation?
No, the IC695PSD040 does not support power supply redundancy or increased capacity modes.
What are the input voltage requirements for start and run operation?
The module requires 18 to 30 VDC to start. It operates across 12 to 30 VDC while running.
What is the indicative market price for the IC695PSD040F?
Observed market reference pricing is around $579. This figure is an indicative market reference only and not a final quotation.
