PRODUCT INFORMATION
Product Overview
The General Electric IC697PWR711 is a Series 90-70 Power Supply Module. This module delivers a total continuous power output rating of 100 Watts. It mounts directly into the leftmost slot of an IC697 rack using a slide-in design. It connects to the backplane via a dedicated 48-pin connector.
The unit supports selectable AC input ranges of 90 to 132 VAC and 180 to 264 VAC. It also operates from a DC source ranging between 100 and 150 VDC. Regulated DC outputs provide +5 VDC, +12 VDC, and -12 VDC to backplane components. Electronic short circuit protection and overcurrent limits safeguard all three output rails during operation.
TECHNICAL DATA
Technical Specifications
| Parameter | Specification |
|---|
| AC Input | 90 to 264 VAC |
|---|
| DC Input | 100 to 150 VDC |
|---|
| Frequency | 47 to 63 Hz |
|---|
| Holdup Time | 21 milliseconds minimum |
|---|
| Input Frequency Range | 47-63 Hz |
|---|
| Input Half Cycle Peak Inrush | 55 amps (typical), 77 amps (maximum) |
|---|
| Input Power | 160 watts maximum at full load |
|---|
| Input Voltage Range, AC | 90-132 VAC / 180-264 VAC |
|---|
| Load Capacity | 100 Watts |
|---|
| No. of Outputs | Three (3) |
|---|
| Nominal rated voltage | 120/240 VAC |
|---|
| Operating temmperature | 0-60 degrees Celsius |
|---|
| Output Voltage | +5 VDC: 4.90 to 5.25 volts (5.07 volts nominal) +12 VDC: 11.75 to 12.6 volts ' -12 VDC: -12.6 to -11.75 volts |
|---|
| Output power | 100 Watts maximum (total for all 3 outputs) |
|---|
| Overcurrent limit | +5 VDC output: 26 amp, maximum +12 VDC output: 4 amp, maximum -12 VDC output: 2 amp, maximum |
|---|
| Overvoltage Limit | +5 VDC Output: 5.7 to 6.7 volts |
|---|
| Power Factor | > 0,93 |
|---|
| Product Line | Series 90-70 |
|---|
| Voltage regulation | 5, 12, and -12 VDC |
|---|
| Weight | 4.50 lbs (2.04 kg) |
|---|
TECHNICAL INFORMATION
Features
- Selectable nominal AC input for 120 VAC or 240 VAC operation.
- Electronic short circuit and overcurrent protection across all outputs.
- Power factor correction exceeding 0.93 under AC input operation.
- Front-panel ON/OFF switch for manual operational control.
- Capable of powering a second rack within total 100 Watt limits.
TECHNICAL INFORMATION
Connections / Interfaces
- Standard 48-pin connector interfaces directly with the IC697 backplane.
- Supports a 3-foot connecting cable to supply power to a secondary rack.
- Terminal jumper configuration determines 120 VAC or 240 VAC input selection.
TECHNICAL INFORMATION
Installation Guidelines
- Install the module exclusively in the leftmost slot of the IC697 rack.
- Slide the module into the rack guides until fully seated into the backplane.
- Derate output specifications when operating in high ambient temperatures.
- Maintain ambient operating temperatures below 60 degrees Celsius.
- Provide appropriately sized external fusing for AC branch circuit protection.
PART VERIFICATION
Before You Order
Industrial automation parts can share similar model names, suffixes and revisions. Confirm the complete manufacturer Part Number before purchase.
01Check Part NumberMatch the complete ordering code on the existing unit.
02Confirm RevisionCheck suffix, hardware or firmware when applicable.
03Send a Label PhotoWe can review a clear label photo when identification is uncertain.
ORDERING PROCESS
From RFQ to Dispatch
1Submit Part Number2Verify Product Identity3Confirm Stock & Condition4Issue Quotation5Dispatch & Tracking
PRODUCT FAQ
Frequently Asked Questions
What input voltages are supported by the IC697PWR711?
It supports 90 to 132 VAC, 180 to 264 VAC, and 100 to 150 VDC.
Can the IC697PWR711 power an expansion rack?
Yes. It can power a second rack using a 3-foot cable within 100 Watts total load.
What is the price of the General Electric IC697PWR711?
Any published pricing reflects indicative market reference values only and is not a final quotation.
