PRODUCT INFORMATION
Product Overview
The General Electric DS200TCQCG1A is an RST Overflow Board developed for the Mark V turbine control system. It functions as an analog IO expander board within compatible gas, steam, and wind turbine assemblies. This printed circuit board features an A-rated functional revision of the parent DS200TCQCG1 hardware design. The module includes normal protective PCB coating to withstand industrial operating environments. Multiple onboard connectors and configurable jumpers support signal distribution across the turbine control system architecture.
Hardware connectivity includes three 40-pin connectors designated as JFF, JE, and 6PL. The assembly also integrates three 34-pin connectors and a single 16-pin connector labeled JC. In addition, twenty-four hardware jumpers provide specific operating adjustments tailored to host facility requirements. Technicians configure these jumper settings during installation to determine internal processing paths. Once configured, jumper settings remain stationary and require no regular adjustments during operational service.
TECHNICAL DATA
Technical Specifications
| Parameter | Specification |
|---|
| PCB Coating | Normal Coating |
|---|
TECHNICAL INFORMATION
Features
- Configured with 24 onboard jumpers for site-specific signal path selection.
- Includes three 40-pin connectors identified as JFF, JE, and 6PL.
- Features three 34-pin ribbon cable interfaces for internal control routing.
- Provides one 16-pin interface connector designated as JC.
- Incorporates factory-applied normal PCB coating for board preservation.
- Delivers an A-rated functional product revision over base DS200TCQCG1 hardware.
TECHNICAL INFORMATION
Applications
- General Electric Mark V gas turbine management systems.
- Steam turbine drive control and monitoring platforms.
- Wind turbine automation and control drive assemblies.
TECHNICAL INFORMATION
Connections / Interfaces
- Three 40-pin connectors designated JFF, JE, and 6PL.
- Three 34-pin connection interfaces.
- One 16-pin connector designated JC.
TECHNICAL INFORMATION
Installation Guidelines
- Wear a grounding wrist strap before handling the printed circuit board.
- Place the unpowered defective board on a clean, flat surface.
- Remove the replacement board from its static protective enclosure.
- Inspect all twenty-four jumpers and mirror positions from the old board.
- Verify that all ribbon connectors seat securely into JC, JE, JFF, and 6PL.
TECHNICAL INFORMATION
Configuration Guidelines
- Review facility documentation and installation guides before altering jumper pins.
- Configure the 24 jumpers to match site requirements during initial drive setup.
- Retain confirmed jumper positions to maintain processing logic across operational cycles.
TECHNICAL INFORMATION
Compatibility
- Designed for integration within General Electric Mark V turbine control assemblies.
- Serves as an A-revision alternative to the unrevised DS200TCQCG1 board design.
TECHNICAL INFORMATION
Lifecycle / Replacement Information
- Defective boards can be replaced by duplicating jumper settings onto the spare unit.
- Match jumper arrangements before inserting the replacement card into the system.
COMPATIBILITY
Compatibility & Replacement
COMPATIBLE MODELSDesigned for integration within General Electric Mark V turbine control assemblies. Serves as an A-revision alternative to the unrevised DS200TCQCG1 board design.
Verify compatibility against the exact Part Number, revision and manufacturer documentation before ordering.
PART VERIFICATION
Before You Order
Industrial automation parts can share similar model names, suffixes and revisions. Confirm the complete manufacturer Part Number before purchase.
01Check Part NumberMatch the complete ordering code on the existing unit.
02Confirm RevisionCheck suffix, hardware or firmware when applicable.
03Send a Label PhotoWe can review a clear label photo when identification is uncertain.
ORDERING PROCESS
From RFQ to Dispatch
1Submit Part Number2Verify Product Identity3Confirm Stock & Condition4Issue Quotation5Dispatch & Tracking
PRODUCT FAQ
Frequently Asked Questions
What is the primary function of the General Electric DS200TCQCG1A?
The board acts as an RST overflow board and analog IO expander within Mark V systems. It manages signal routing across compatible steam, gas, and wind turbine assemblies.
How should technicians configure jumpers during replacement of the DS200TCQCG1A?
Technicians should place the original board on a flat surface while wearing an ESD wrist strap. Align the replacement board and match its twenty-four jumper positions to the original settings.
What connectors are installed on the DS200TCQCG1A board?
The board includes three 40-pin connectors (JFF, JE, 6PL), three 34-pin connectors, and one 16-pin connector (JC).
